74121 MONOSTABLE MULTIVIBRATOR PDF

Description and operation of a 74L and Monostable Multivibrator. The shown above provides a single Monostable Multivibrator function. SNN from TEXAS INSTRUMENTS >> Specification: Monostable Multivibrator, , 45 ns, 16 mA, V to V, DIP MONOSTABLE MULTIVIBRATOR WITH SCHMITT TRIGGER INPUT This multivibrator features dual negative-transition-triggered inputs and a single.

Author: Faekasa Zulurisar
Country: Russian Federation
Language: English (Spanish)
Genre: Photos
Published (Last): 5 February 2004
Pages: 215
PDF File Size: 13.19 Mb
ePub File Size: 17.37 Mb
ISBN: 634-7-32536-379-3
Downloads: 95070
Price: Free* [*Free Regsitration Required]
Uploader: Goltikinos

All this allows to create very simple frequency meter circuit with several frequency ranges: How to calibrate this frequency meter?

The pulse frequency depends on the input frequency. This IC is the monostable multivibrator that may generate a pulse of a different width from 35 ns and wider that depends on RC components. VD4 protects the integrated circuit from overloading. The two graphs below show the resultant pulse width for different values of resistors and capacitors.

Turn the rotary switch S1 of the frequency meter to the range of Hz and connect the device to the reference signal source of Hz.

A quartz crystal oscillator circuit that can generates kHz signal with a 3-stage decade counter can be used as a reference frequency source see the Figure 2. To use the internal timing resistor connect Rint to Vcc. The pin out diagram works any any style 74xx or 74xx DIP chip, but the timing graphs are only valid for the TTL families indicated.

  IP6 INOSITOL PDF

The pulse voltage is proportional to the input frequency, through the diode VD5 this voltage charges the capacitor C1. Also refer to Transistor Multivibrator Circuits. Note the uses a 4k internal resistor, while the uses a 20k resistor. This device uses the ammeter with full-scale deflection of 0. Adjust the trimming potentiometer R3 to move the needle of ammeter PA1 to the maximum value on the scale. The Diodes used in the circuit are 1N or equivalent.

74121 – Monostable Multivibrator

The first method for a Cx of less than pF [below] and a second connection [below that] for an external capacitor, Cx, of greater than pF. Reference oscillator circuit diagram.

The Figure 1 shows the circuit diagram of the frequency meter, the circuit based on the digital IC By the way, the ammeter PA1 can be replaced with a digital multimeter. While the shown below provides a retriggerable Monostable Multivibrator function with clear.

There are two different methods of connecting Rx and Cx. The first chart works for either the 74L or 74L; however, the second chart only applies to the 74L The circuit could be used for any TTL family, such as LS, or H, but the load capacitor might need to be changed to reflect that.

Electronic Engineering Dictionary

Digital integrated circuits can be used in the design monostabe an analogue frequency meter with a frequency range to several MHz. Instead ofthe SN or DM can be used. The device can measure sinusoidal wave multivlbrator square wave input signals. All this allows to create very simple frequency meter circuit with several frequency ranges:. You’ll need a source of stable frequency reference signal that can produces a set of frequencies Hz, 1 kHz, 10 kHz and kHz.

  ALVIN PLANTINGA WHERE THE CONFLICT REALLY LIES PDF

How to Read Logic Truth Tables: Frequency meter with monostable multivibrator Digital integrated circuits can be used in the design of an analogue frequency meter with a frequency range to several MHz.

– Monostable Multivibrator

A Monostable Multivibrator is also called a One Shot. Do the same operation for all ranges. The ammeter PA1 indicates the voltage across the capacitor C1. The number of frequency ranges can be increased by using a rotary switch SA1 with more than four positions, and by adding some additional RC components. C5 and trimming potentiometers R The shown above provides a single Monostable Multivibrator function.

The pulse width produced by the monostable multivibrator depends on the values of capacitors C The load Capacitance CL is 50pF, including scope probe, wiring, and any stray capacitance.