Advanced Melt Flow System. The 6MPCA is the most advanced digital model offered within the Ray-Ran range of melt flow index testers. The operating. Find the most up-to-date version of ASTM D at Engineering ASTM D(). Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications. standard by ASTM.

Author: Kajigor Kajicage
Country: Spain
Language: English (Spanish)
Genre: Relationship
Published (Last): 13 January 2009
Pages: 348
PDF File Size: 20.71 Mb
ePub File Size: 16.42 Mb
ISBN: 426-9-79467-918-8
Downloads: 14552
Price: Free* [*Free Regsitration Required]
Uploader: Shakus

As a guide, each specimen should be about 20 to 30 mm d3634. Description Contact Us This test method is used for quality-control tests on PVC compounds that have a wide range of melt viscosities. For PVC, N varies from 0. An alternative thermoregulator is suggested for improved temperature control.

Concrete, Asphalt and Rock. This weight is effective for all semirigid PVC and even some nonrigid compounds. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Please confirm that you agree with our privacy and cookies policy to submit this form.

ASTMD Standard Test Method for Poly(Vinyl ride) with Molecular Structural Implications_百度文库

Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more! These changes are due to three types of measured instability in polymers:.

If instability still occurs, particularly at high? The following explanations of r and R The data in Table 3 should not be rigorously applied to acceptance or rejection of material, as those data are speci?

ASTM D Flow Rates for Poly Vinyl Chloride – Instron

These changes are due to three types of measured instability in polymers: Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. By changing the die, approximately a tenfold increase in? Most regulators designed for Test Method D cannot control better than Summary of Test Method 4. Each laboratory obtained three test results for each material.


When charging is complete, pack down the PVC with the phenolic-coated charging tool by repeated thrusts.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The principles of The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not ast, standard.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Due to the corrosive properties of PVC materials, the instrument was equipped with a special corrosion resistant kit to prevent any interaction between the material and the metal during testing.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Software for Series Systems. WaveMatrix 2 for Dynamic Testing. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

ASTM D3364 – 99(2011)

The sensitivity of the material to temperature necessitates slightly tighter controls than those stated in Test Method D Each test result was the average of? This statement further de? Report as percent PVC instability. A s3364 instability indicates either a degradation of the polymer or a change in the lubricant function at the metal surface of the die. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


Since Q is the volumetric?

Pass the tip of the spatula upward along one side of the beveled aastm, lightly across the bottom of the ori? The quantity of material introduced into the barrel is 2. At least twice a day check the ori? Users of this test method should apply the principles outlined in Practice E to generate data speci?

If the difference between the two specimens is greater than 0. Make the cut quickly and neatly for best precision. The entire time of charging and positioning of weights should take no longer than 1 min and preferably less than 1?

ASTM D3364 Flow Rates for Poly Vinyl Chloride

How can we help you? For each material, all the samples were prepared at one source, but the individual specimens were prepared at the laboratories which tested them. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Thus, this test is able to detect and follow profound changes which occur during extrusion, injection molding, milling, or mixing. Historical Version s – view previous versions of standard.

Email addresses can only contain letters, numbers and the following special characters: Subscribe to Instron News!