DM311 DATASHEET PDF

DM – Download as PDF File .pdf), Text File .txt) or read online. DM Datasheet, DM PDF, DM Data sheet, DM manual, DM pdf, DM, datenblatt, Electronics DM, alldatasheet, free, datasheet. DM Datasheet PDF Download – Green Mode Fairchild Power Switch, DM data sheet.

Author: Ketilar Mejora
Country: Mexico
Language: English (Spanish)
Genre: Education
Published (Last): 14 January 2010
Pages: 195
PDF File Size: 4.61 Mb
ePub File Size: 14.97 Mb
ISBN: 911-7-11475-231-8
Downloads: 78769
Price: Free* [*Free Regsitration Required]
Uploader: Naktilar

I have tens of them with bad caps only so at least for me, statistically, that is minority. Hopefully they will help you to understand the circuits better. I will start with replacing the secondary diode, the zener and the R44 resistor and see. CT as well as 24 datashedt.

Included PWM controller integrates the fixed frequency oscillator, the undersuited for cost effective design of flyback converters. Anyway, thanks for your cm311 input, I see these PSUs quite a lot, but never had time to dive so much much into these tanks of shit Please keep us posted.

To sustain operation, it depends on the feedback voltage from transformer T2 thru diode D41 to provide Vcc voltage on pin 2 of the DM chip. Typical operation on this power supply, it should reach and maintain 12 volts. Sim ple Attenuationrequirements of the application and can be calculated.

DM Datasheet catalog

Also, if the Vcc goes above 20 volts it turns off. Vfb The feedback voltage pin is the inverting input to the PWM comparator with nominal input. Than the zener is supposed to do all the work and can go short…. Now I don’t fix two transistor 5vsb circuits on Bestecs.

  GOTTFRIED BAMMES SEHEN UND VERSTEHEN PDF

Hopefully this information helps.

DM311 Datasheet PDF – Fairchild Semiconductor

It is the same board under the Sparkle brand. I am including some photos of that power supply and the drawings I made. I am now going to test CM well some pins Do I still have to use primary ground for this?

Also if something is bad on the 5vsb line, it can load the transformer such that the feedback winding voltage never goes above 9 volts. It istransformer will decrease leakage inductance. Worked great and no more dm311 headaches. In the end, I took the basic 5vsb design using the DM from the Fortron GLN series, put the parts on a small piece of perf-board, and installed it on the Bestec.

And here are some drawings Attached: But digging further it looks alright. A potentiometer tied between the 1. Check the voltage on pin 2.

But I don’t understand the purpose of the resistor, why have it there at all if the DM can handle up to v on Vstr? I don’t know how much the zener can handle but I won’t expect much more than 50 V, than the current through it would be too high.

No abstract text available Text: Originally Posted by everell: Perhaps the large capxon cap started to go bad, and the PFC circuit worked harder to maintain the voltage, overheating the PFC coil and shorting out the DM from high voltage spikes?

So I think huge resistor is there to ensure slow enough charging of the Vcc cap otherwise there would be huge spike through the IC, auxiliary transformer windig and to the cap.

  HP M1319F PDF

The voltage on pin 2 of the DM must be above 9 volts, typically 12 volts. So you need to replace them all, every time. But how come I end up with the really bad ones??? A minimum throughput rate of KHz Is achieved while only dissipating 1. Oh my bad, I’ve been talking about Vcc…the Vstr should consume uA. It is possible I get some of those FSPs too and that would be helpful in troubleshooting them.

Do I still have to use primary ground for this? However, what usually goes bad because of excessive overheating due to using that GP diode and no cooling, and because of poor quality, is the cap. Step 7 – Generation of driver code. I did a comprehansive study on this power supply board a few years ago.

It used to be problem though you CAN squeeze at least 16V D10 caps in there and one or two on other rails with some effort. Click any of the following links to jump to the.

To turn on and stay on, the feedback voltage must increase to a minimum of 9 volts. I have not seen a PSU of this type where they were not so replacing them is a must. It may start with no load making an impression it is actually OK.