Notice: OMRON products are manufactured for use according to proper procedures .. You can install multiple 3G3JX inverters side by side in the control panel. Simple, Compact Inverters SYSDRIVE JX Series . Model name (3G3JX-) In no event shall the responsibility of OMRON for any act exceed the individual. Inverter 3G3JX . Use this terminal block to connect the inverter to the Sysmac® is a trademark or registered trademark of OMRON Corporation in Japan and.
| Author: | Faern Mazushakar |
| Country: | Malawi |
| Language: | English (Spanish) |
| Genre: | Spiritual |
| Published (Last): | 19 May 2017 |
| Pages: | 281 |
| PDF File Size: | 13.54 Mb |
| ePub File Size: | 17.95 Mb |
| ISBN: | 748-2-61988-663-1 |
| Downloads: | 42813 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Nikoll |
Connect securely to the ground as specified type-D grounding for V class, and type-C grounding for V class. Be sure to follow the instructions. This helps display the actual physical value on the monitor. Note that the actual deceleration time may be longer than the set value.
OMRON 3G3JX USER MANUAL Pdf Download.
OL overload warning selection Connect a termination resistor separately to avoid signal reflection, since this 3G3JX does not incorporate it. Okron Options Page Function Mode Function code Maximum number of data Maximum data number in 1 Function code Function bytes in 1 message message Coil status reading 32 coils in bits Holding register content reading 4 3g3hx in bytes Writing into the coil 1 coil in bits Writing into holding register 1 registers in bytes Page Function Mode Message configuration: Network error Network error LOG: Example Multi-function input terminals S4, S2: Be careful, especially if you set a base frequency at below 50 Hz.
OFF Binary operation 2: If the offset C is changed, the point to reach 10 V changes accordingly because of par- allel movement. Page Inverter is shortened.
Chapters Table Of Contents Key sequence Display example Description k0. Page 16 Contents Invegter Example Wiring work must be carried out only by qualified personnel.
Normal operation A selection The smoothing capacitor, which will waste due to the chemical reaction caused by parts tempera- tures, should normally be replaced once every 5 years. Below are the contact specifications of the relay output. This helps prevent data rewrite due to erroneous operation.
Change the 1st digit of the function code. Enter text from picture: The Inverter does not allow this function.
Omron 3G3JX User Manual
CF2 multi-step speed setting binary 2 C 1 selection When forcibly stopping the load with an MC on the primary side of the main circuit, however, the regenerative braking invedter not work and the load coasts to a stop free run.
Factory Default “A” is displayed. The aim of this function is the same as the overvoltage control function during deceleration, described in b and b Performance data given in this manual is provided as a guide for the user in determining suitability and niverter not constitute a warranty. Dimensions And Weights Performance data given in this manual is provided as a guide for the user in determining suitability and does not constitute a warranty.
The following shows their operations.
Do not share the grounding electrode with other strong electrical devices. The setting corresponds to the range of 0 to the maximum target value.
Lift the bottom of the front cover to remove while holding the body. Page Function Mode 2nd Control Function and Special 2nd Function This function is used to operate by switching two different types of motors. This helps prevent mechanical damage due to an overload, or a conveyor line stop due to an over- load trip of the Inverter.
Output current monitor Connect a noise filter to the output side of the Inverter to reduce induction and radio noise. Chapter 2 Design Chapter 2 Design Installation FI input only A FV start frequency 0. The extended function mode is displayed as “A”. Page 62 Operation Procedure Example: Don’t show me this message again.
Data Symbol Function name Status Description Calculates the set value in A against the set frequency in A according to the formula specified in A, in Frequency addition order to provide a new frequency reference. Alarm output for momentary power interruption and undervoltage during stop Examples 3 and 4 Example 3 b While proportional from 0 Hz to base frequency, the output voltage is constant from base to maximum frequencies regardless of the frequency.